Вторник, 24.10.2017, 06:13
  Ремонт принтеров • Ремонт копиров Ремонт МФУ • Заправка картриджей                                                           Приветствую Вас Гость | RSS
Меню сайта
Курсы валют на PROext
  

Категории каталога
Мои статьи [0]
Компьютеры,программы и интернет [12]
Немного о ПК + программы
Проблемы с офисной техникой [21]
Полезные советы и рекомендации
О выборе офисной техники [19]
Правильно выбрать офисную технику
Анимация [2]
Все про анимацию и смайлики
Из истории развития офисной техники [7]
Как это было
Из истории создания [12]
Как появилось и создавалось...
Ремонт офисной техники [16]
Советы по ремонту,ссылки и многое др.
Коды ошибок копировальных аппаратов,принтеров,МФУ [16]
Основные коды ошибок,сброс
Заправка картриджей [16]
Инструкции по заправке лазерных и струйных картриджей,а также, все о чернилах и тонере.
Чипы [7]
Все о чипах в принтерах,МФУ и копирах
Словарь терминов [13]

Главная » Статьи » Коды ошибок копировальных аппаратов,принтеров,МФУ

Коды ошибок аппаратов Toshiba
Toshiba 1340, 1350 
Code Description
C5, C6 Scan problem
C7 Fuser problem (reset with 0 & 5 mode, code 89)
CE Missing EEPROM
CF Board problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E5 Paper feed jam
E0 Toner waste bottle is full

Toshiba 1550 
Code Description
C01 Main motor drive problem
C21 Optics problem Scan, lens, mirror
C26 Exposure lamp detect problem
C32 Setup error (UA)
C41 Fuser thermistor, or no heat
C43 Fuser thermistor problem or other fuser problem, after machine goes into ready
C44 Heater problem
C54 Communication problem between sorter and machine main board
C55 Communication problem between ADF and machine main board
C71 ADF drive problem
C72 ADF registration sensor problem
C73 EEPROM initialization problem
C81 Sorter paper conveying motor
C82 Sorter bin motor
C83 Sorter upper sensor
C84 Sorter lower sensor
C85 Sorter home sensor
C86 Sorter copy removal sensor
C94 Optics initialization problem in test modes
E01 Paper jam
E02 Fuser jam
E03 Paper jam
E05 Paper feed jam
E14 lower cassette jam
E71, E72, E73 ADF jam
E75 ADF jam of 2nd original
E81, E82 Sorter jam

Toshiba 1650 
Code Description
A4 Sorter problem
A5 Communication problem between main CPU and IPC
A6 Sorter interface problem
C2 Communication problem between CPU's
C5 Scan or optic problem. Locked up or won't initialize or return to home position
C7 Fuser problem. After repairing problem, go to «0 & 8 mode», code 87 to reset
CF Developer calibration problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E4 Front door opened during copy cycle
E5 Paper feed jam

Toshiba 1710 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam

Toshiba 2050 
Code Description
A4 Sorter problem
A5 Communication problem between main CPU and IPC
A6 Sorter interface problem
C2 Communication problem between CPU's
C5 Scan or optic problem. Locked up or won't initialize or return to home position
C7 Fuser problem. After repairing problem, go to «0 & 8 mode», code 87 to reset
CF Developer calibration problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E4 Front door opened during copy cycle
E5 Paper feed jam

Toshiba 2060 
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold «0» & «8» keys while turning power on. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the # keys, press «0» & «9» at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter

Toshiba 2310 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam

Toshiba 2500 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam

Toshiba 2510 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam

Toshiba 2532 
Code Description
A4 Sorter problem
A5 Communication problem with main board
A6 Communication problem with sorter
A7 Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2 Communication problem between main board
C5 Scan won't initialize or won't move
C7 Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89 
CC ADF belt motor or exit motor not turning 
CF Auto toner adjustment did not take 
CP Drive problem in machine 
E1 Jam 
E2 Fuser jam 
E3 Jam 
E4 Front door was opened during copy cycle 
E5 Feed jam 

Toshiba 2540 
Code Description
A4 Sorter problem
A5 Communication problem with main board
A6 Communication problem with sorter
A7 Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2 Communication problem between main board
C5 Scan won't initialize or won't move
C7 Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89 
CC ADF belt motor or exit motor not turning 
CF Auto toner adjustment did not take 
CP Drive problem in machine 
E1 Jam 
E2 Fuser jam 
E3 Jam 
E4 Front door was opened during copy cycle 
E5 Feed jam 

Toshiba 2810 
Code Description
C1 Scan did not return home
C3 Scan home sensor
C4 Scan problem
C5 Scan limit sensor
C6 Scan did not return
C7 Thermistor or other fuser problem
CC Scan did not leave home
CP Drive
E1 Jam inside machine
E2 Fuser jam or exit jam
E3 Exit switch or registration switch
E5 Paper feed jam
E7 Cassette or registration jam

Toshiba 2860 
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold «0» & «8» keys while turning power on. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the # keys, press «0» & «9» at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter

Toshiba 2870 
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold «0» & «8» keys while turning power on. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the # keys, press «0» & «9» at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter

Toshiba 3210 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam

Toshiba 3220 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam

Toshiba 3550 
Code Description
A1 Transfer/separator
A2 Duplex problem
A3 PFC CPU malfunction
A4 Sorter problem
A5 Communication problem between main board and IPC
A6 Sorter board to copier communication problem
A7 Communication problem between copier and RADF
A0 Communication main board problem
C3 Communication problem between main board and sub processor
C5 Optics locked or not initialized
C7 Fuser problem. Reset required. Turn off power. Hold «0» & «8» keys while turning on power. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the number keys, press «0». Then press «interrupt». Then press «0» & «9» at the same time
CB ADF feed motor drive problem
CC ADF transport motor drive problem
CP Copier main motor drive problem
E1 Jam
E2 Fuser jam
E3 Jam at turn on
E4 Front door opened during copy cycle
E5 Registration jam
E8 Duplex unit jam
E9 Jam in paper feed unit pedistal
EC ADF jam
ED ADF transport jam
EE ADF exit or reversing jam

Toshiba 3560 
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold «0» & «8» keys while turning power on. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the # keys, press «0» & «9» at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter

Toshiba 3570 
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold «0» & «8» keys while turning power on. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the # keys, press «0» & «9» at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter

Toshiba 3810 
Code Description
C5 Scan problem
C7 Heater problem
CD EEPROM at end of life
CE EEPROM/main board problem
CF DV unit out or toner sensor problem
CP Drive
E1 Paper jam before exit
E2 Exit jam
E3 Jam
E5 Cassette jam
E6 Bypass jam
E0 Waste toner full

Toshiba 3910 
Code Description
C5 Scan problem
C7 Heater problem
CD EEPROM at end of life
CE EEPROM/main board problem
CF DV unit out or toner sensor problem
CP Drive
E1 Paper jam before exit
E2 Exit jam
E3 Jam
E5 Cassette jam
E6 Bypass jam
E0 Waste toner full

Toshiba 4010 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam

Toshiba 4111, 4121 
Code Description
C1 Scanner not home
C2 First paper path switch or sub processor
C5 Scan stop switch
C5 Scan won't stop
C7 Fuser problem
C8 Lens
C9 Check 24V

Toshiba 4560 
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold «0» & «8» keys while turning power on. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the # keys, press «0» & «9» at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter

Toshiba 4570 
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold «0» & «8» keys while turning power on. Then press «8». Then press «9». Then press «print». You will read «3» in the display. Using the # keys, press «0» & «9» at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter

Toshiba 4810 
Code Description
C1 Scan not home
C2 Scan did not leave home
C3 Forward scan
C4 Forward scan (dual page mode)
C5 Scan limit
C6 Scan return
C7 Thermistor
CP Motor lock
E1 Fuser jam
E2 Exit jam
E3 Jam
E5, E7 PF jam

Toshiba 4910 

Code Description
C4 Cam switch
C5 Optics
C7 Thermistor or fuser
C8 Scan motor stays on
CE Main board
C0 Dead battery
CP Drive
E1 Jam
E2 Fuser jam
E3 Jam at turn on
E4 Door opened during copy run

Toshiba 5010 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC, ED ADF jam
EE ADF exit/reverse jam

Toshiba 5020 
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB, CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC, ED ADF jam
EE ADF exit/reverse jam

Toshiba 5120 
Code Description
C2 Signal to sub processor
C4 Cam motor
C5 Optics
C7 Thermistor or fuser problem
CD Weak battery
CE Battery disconnected
C0 DV select problem
CP Drive
E1 Jam
E2 Fuser jam
E3 Jam after turning on
E4 Door opened during run
E5 Lower cassette jam
E6 Upper cassette

Toshiba 5510 
Code Description
C2 Signal to sub processor
C4 Cam motor
C5 Optics
C7 Thermistor or fuser problem
CD Weak battery
CE Battery disconnected
C0 DV select problem
CP Drive
E1 Jam
E2 Fuser jam
E3 Jam after turning on
E4 Door opened during run
E5 Lower cassette jam
E6 Upper cassette

Toshiba 5511
 
Code Description
C5 Initializing
C6 Home switch
C7 Thermistor
C8 Scan motor on
C9 Scan problem
E0 Waste toner bag full
E1 Jam
E2 Fuser jam
E3 Exit jam
E4 Front door

Toshiba 5610, 5620 
Code Description
C0 DV select switch or motor problem
C1-C4 Signal from sub processor (motor control board)
C5 Optics
C6 Home sensor
C7 Fuser
C8 Scan
CA Sub processor
CD Weak battery
CE Battery disconnected
CP Main motor

Toshiba 727, 728 
Code Description
01 Scanner problem
02 Paper jam or path switch
03 Exit switch problem
04 Jam or paper on drum
05 Jam or false jam

Toshiba 7610 
Code Description
C2, C3 Board
C4 Cam switch
C5 Optics
C7 Thermistor
C8 Scan motor
CD EEPROM dead
CE EEPROM
CP Drum motor
E1 Jam
E2 Fuser jam
E3 Jam
E4 Interlock
E5 PF (lower cass. )
E6 PF (upper cass. )

Toshiba 7720 
Code Description
A1 Spot motor
A2 Duplex guide
C0 Developer shift motor
C2 Signal main board
C3 Signal from main board
C4 Cam switch
C5 Optics have not moved
C7 Thermistor or cold warm up
C8 Scan motor
CD Eprom dead
CE Eprom
CP Drum/fuser motor
E1 Jam
E2 Fuser jam
E3 Jam
E4 Interlock opened during copy cycle
E5 Paper feed jam from lower cassette
E6 Paper feed jam from upper cassette

Toshiba 7812, 7815, 7816 
Code Description
C5 Initializing
C6 Home Switch
C7 Thermistor
C8 Scan motor
C9 Scan problem
CA Scan switch
CC ADF motor
E0 Waste toner bag full
E1 Jam
E2 Fuser jam
E3 Exit Jam
E4 Front door

Toshiba 7910 
Code Description
C0 Paper feed cam switch problem
C2 Bad signal to main board
C3 Bad signal from main board
C5 Optics
C7 Fuser problem
C8 Scan motor staying on
CC Document feeder problem
CE Battery or memory problem
CP Drive
E1 Jam
E2 Fuser jam
E3 Jam
E4 Door was opened during job
E5 Paper feed jam

Toshiba 8412 
Code Description
C0 Cam motor
C1 Signal to color sub processor
C2 Signal to black sub processor
C3 Signal from color sub processor
C4 Signal from black sub processor
C5 Initializing
C6 Scan home switch
C7 Thermistor
C8 Scan motor
C9 Scan
CA Document feeder
CB Memory
CC Document feeder
CE Memory
E0 Toner bag
E1 Jam
E2 Fuser jam
E3 Exit jam
E4 Front

Toshiba 8510 
Code Description
C0 Cam switches on cam motor
C2 Bad signal to sub processor
C3 Bad signal from sub processor
C5 Scan does not initialize
C7 Heater problem
C8 Scan motor stays on
CC ADF
CD Weak battery in memory EPROM
CE Memory disconnected
CP Drive problem
E1 Jam
E2 Fuser jam
E3 Jam
E4 Door opened during copy
E5 Feed jam

Toshiba 8812 
Code Description
C5 Initializing
C6 Home switch
C7 Thermistor
C8 Scan motor on
C9 Scan problem
CA Scan Switch
CC ADF motor on
E0 Waste toner bag full
E1 Jam
E2 Fuser jam
E3 Exit Jam
E4 Front door

Toshiba 9110 
Code Description
A1 Charge corona cleaner problem
A2 Duplex problem
C0 Cam motor
C1 Bad input to upper logic subprocessor
C2 Bad input to lower logic subprocessor
C3 Bad output from upper subprocessor
C4 Bad signal from lower subprocessor
C5 Optics problem at turn on
C6 Scan home switch
C7 Thermistor or fuser problem
C8 Scan motor stays on
C9 Scan problem
CA Indicators
CB Memory
CC Motor stop signal present too long
CE Software problem
E0 Toner bag full
E1 Jam
E2 Fuser jam
E3 Exit jam
E4 Door opened during run

Toshiba 9230 
Code Description
A1 Charge corona cleaner
A2 Duplex problem
C1 Board problem. Input to upper logic subprocessor
C2 Board problem. Input to lower logic subprocessor
C3 Board problem. Output to upper logic subprocessor
C4 Board problem. Output to lower logic subprocessor
C5 Optics locked or not initialized. Could be scan or lens mirror
C6 Scan home switch
C7 Fuser thermistor problem, or low temp
C8 Scan motor won't shut off
CA Indicators
CB Memory
CC Motor stop signal present too long
CE Software
C0 Paper feed cam motor problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam


Категория: Коды ошибок копировальных аппаратов,принтеров,МФУ | Добавил: avatar (08.08.2009)
Просмотров: 2225 | Рейтинг: 0.0/0 |
Форма входа

Поиск

Друзья сайта

Статистика


Copyright MyCorp © 2017