Вторник, 24.10.2017, 06:11
  Ремонт принтеров • Ремонт копиров Ремонт МФУ • Заправка картриджей                                                           Приветствую Вас Гость | RSS
Меню сайта
Курсы валют на PROext
  

Категории каталога
Мои статьи [0]
Компьютеры,программы и интернет [12]
Немного о ПК + программы
Проблемы с офисной техникой [21]
Полезные советы и рекомендации
О выборе офисной техники [19]
Правильно выбрать офисную технику
Анимация [2]
Все про анимацию и смайлики
Из истории развития офисной техники [7]
Как это было
Из истории создания [12]
Как появилось и создавалось...
Ремонт офисной техники [16]
Советы по ремонту,ссылки и многое др.
Коды ошибок копировальных аппаратов,принтеров,МФУ [16]
Основные коды ошибок,сброс
Заправка картриджей [16]
Инструкции по заправке лазерных и струйных картриджей,а также, все о чернилах и тонере.
Чипы [7]
Все о чипах в принтерах,МФУ и копирах
Словарь терминов [13]

Главная » Статьи » Коды ошибок копировальных аппаратов,принтеров,МФУ

Коды ошибок аппаратов Canon IR2200 /IR2800 /IR3300
Код ошибки
Субкод
Описание
E000
0000
The reading of the main thermistor does not reach 30oC 1 sec after the main power switch is turned on. Or, it does not reach 70oC 2 sec thereafter
E001
0000
The main thermistor detects 250oC or higher
0001
The main thermistor or the sub thermistor detects overheating (hardware circuit detection)
0002
The sub thermistor detects about 295oC or higher
E002
0000
The temperature of the fixing film is as follows:
  • has exceeded 100oC, but does not reach 115oC within 1 sec thereafter.
  • has exceeded 140oC, but does not reach 150oC within 1 sec thereafter.
  • has exceeded 160oC, but does not reach 165oC within 1 sec thereafter
  • E003
    0000
    The main thermistor reading is lower than 140oC when paper is moved
    0001
    Low fixing temperature detection after standby (by sub thermistor)
    E007
    0000
    An error in the rotation of the fixing film is detected.
    The reading of the main thermistor is 100oC or higher and, in addition, the fixing film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven
    E010
    0000
    After the main motor drive signal is generated, the clock signal does to arrive within 1.3 sec
    E014
    000
    After the fixing motor drive signal is generated, the clock signal does not arrive within 1.3 sec
    E019
    0000
    The waste toner case is full of waste toner
    E032
    0001
    The DA unit connection is disconnected (after connection).
    E051
    0000
    At start-up, home position is not detected when the horizontal registration assembly is moved 100 mm in the direction of home position
    E064
    0000
    The presence of a high-voltage error is communicated by the composite power supply PCB (The output for primary charging, developing, or transfer has deviated from a specific level of voltage)
    E100
    0001
    The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal
    0001
    The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal
    0002
    While the laser is ON, the BD signal cycle is outside a specific range 20 times or more continuously
    0003
    While the laser is ON, the horizontal sync signal cycle is outside a specific range 20 times or more
    E110
    0000
    The motor ready signal does not arrive within 15 sec after the laser scanner motor drive signal is generated
    E202
    0001
    The scanner home position sensor does not go OFF when the scanner is moved forward by 40 mm
    0002
    The scanner home position sensor does not go ON when the scanner is moved reverse 450 mm
    E204
    0001
    While an original is being read, the image leading edge signal does not arrive from the ADF
    E220
    0001
    A fault is detected on the inverter PCB for the scanning lamp
    E225
    0000
    A specific level cannot be attained for the signal during CCD gain correction at power-on
    0002
    The edge gain correction level is different from the correction level for the preceding sheet by a specific level or more
    E240
    0000
    A fault occurs in communication between the CPU of the main controller PCB and the CPU of the DC controller PCB
    E243
    0000
    A fault occurs in the communication between the CPU of the control panel PCB and the CPU of the main controller PCB
    E248
    0001
    A difference is discovered between the ID in EEPROM read when the main power switch is turned on and the ID in ROM upon comparison
    0002
    The data read does not match the data written to EEPROM
    0003
    A difference is discovered between the ID of EEPROM and the ID of ROM upon comparison while writing data
    E261
    0000
    The intervals of zero-cross signals deviate from the tolerance range while the fixing heater is supplied with power
    E302
    0001
    During shading, the shading processing does not end on the reader controller PCB after 1 sec
    0002
    During stream reading, the edge white addition processing does not end on the rear controller PCB after 10 sec
    E315
    -
    Any of the following is true in the image processing by the main controller:
  • The image data has a fault
  • The encoding/decoding operation for image data has a fault
  • The image processing element of the main controller PCB has a fault
  • E601
    0000
    When an image is transferred between the main controller PCB and the HDD, the main controller PCB detects a fault in control information
    0001
    When an image is transferred between the main controller PCB and the DC controller PCB, the DC controller PCB detects a fault in the control information
    E602
    0001
    A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM
    0002
    A data read fault of the HDD is detected when the HDD is started up from the BOOT ROM
    E604
    0000
    A fault is detected in the image memory
    E605
    0001
    A fault is detected in the battery for the image memory
    E606
    0001
    A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM
    E674
    0000
    A faulty occurs in the communication between the fax PCB and the main controller PCB
    E677
    0001
    A fault occurs it the combination between any of the printer boards (accessories) and the main controller PCB
    E710
    0001
    When the main power is turned on, the communication IC (IPC) on the reader controller PCB cannot be initialized
    0002
    When the main power is turned on, the communication IC (IPC) on the DC controller PCB cannot be initialized
    0003
    When the main power is trend on, the communication IC (IPC) on the main controller PCB cannot be initialized
    E711
    0001
    Data is written to the error register of the communication IC (IPC) on the reader controller PCB four times or more within 1.5 sec
    0002
    Data is written to the error register of the communication IC (IPC) on the DC controller PCB four times or more within 2 sec
    0003
    Data is written to the error register of the communication IC (IPC) on the main controller PCB four times or more within 2 sec
    E712
    0001
    The communication is not resumed 3 sec or more after data has been written to the error register of the communication IC (IPC) on the ADF controller PCB
    0002
    The transmission bit is not enabled 10 sec or more in the sync register of the communication IC (IPC) on e reader controller PCB
    E713
    0000
    The communication with the finisher is not resumed 3 sec or more after it is disrupted
    E716
    0000
    The ID signal is not detected within a specific period of time after the presence of a pedestal is detected
    E719
    0000
    Erroneous communication with card reader (serial communication)
    0002
    Erroneous communication with coin vender (serial communication)
    E717
    0001
    The communication with the DA unit is not resumed 3 sec or more after it is disrupted
    E719
    0001
    The communication between the Card Reader-C1 or the coin vendor and the main controller PCB is disrupted
    E732
    0001
    A fault is detected by the main controller PCB in the communication between reader controller PCB and the main controller PCB
    E733
    0001
    A fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB
    E737
    0000
    During self diagnosis at power-on, the DRAM check finds a fault in the main controller PCB
    E740
    0001
    At power-on, the LAN card has a fault
    0002
    The MAC address has a fault
    0003
    The LAN card cannot be read
    E741
    0000
    The PCI bus has a fault
    E743
    0000
    The reader controller PCB detects a fault in the communication between the main controller PCB and the reader controller PCB
    E744
    0000
    The BootROM on the main controller PCB and the system software are for different models or are of different types
    E803
    0000
    The 24V output from the composite main power supply PCB is absent for 1 sec or more
    E805
     
    The clock signal is absent for 5 sec or more after the fan drive signal has been generated. The detail codes of the fans in question are as follows:
    0001
    developing fan (FM1)
    0002
    fixing fan (FM2)
    0003
    curl reducing fan (FM4)
    0004
    curl reducing fan (FM5)
    0005
    electrical unit fan (FM3)
    E901
    0000
    The motor ready signal does not arrive within 1.3 sec after the pedestal main motor drive signal is generated
    ADF Error Codes
    E420
    0001
    When the power switch of the host machine is turned on, the back-up data from the EEPROM cannot be read or the data that has been read has a fault
    E421
    0001
    The back-up data cannot be written to the EEPROM, or the data that has been written has a fault
    E422
    0001
    While the ADF is in standby, the communication with its host machine is disrupted for 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0.5 sec or more
    Saddle Finisher-G1 Error Codes
    E501
    0001
    The communication between the finisher controller PCB and the puncher drive PCB is disrupted
    E505
    0001
    When the main power is turned on, the checksum of the finisher controller PCB has a fault
    0002
    When the main power is turned on, the checksum of the puncher driverPCB has a fault
    E510
    0001
    The feeding roller does not leave home position when the feed motor is driven for 2 sec
    0002
    The feeding roller does not return to home position when the feed motor is driven for 2 sec
    E514
    0001
    The delivery belt does not leave home position when the stack delivery motor is driven for 3 sec
    0002
    The delivery belt does not return to home position when the stack delivery motor is driven for 3 sec
    E530
    0001
    The aligning plate (rear) does not leave home position when the alignment motor (rear) is driven for 3 sec
    0002
    The aligning plate (rear) does not return to home position when the alignment motor (rear) is driven for 3 sec
    E531
    0001
    The stapler does no leave home position when the stapler/folder motor is driven for 1.5 sec
    0002
    The stapler does not return to home position when the stapler/folder motor is driven for 1.5 sec
    0003
    The clock signal is disrupted for 1 sec or more while the stapler/folder motor is driven
    E532
    0001
    The stapler unit does not leave home position when the stapler slide motor is driven for 4.5 sec
    0002
    The stapler unit does not return to home position when the stapler slide motor is driven for 4.5 sec
    E537
    0001
    The aligning plate (front) does not leave home position when the alignment motor (front) is driven for 3 sec
    0002
    The aligning plate (front) does not return to home potion when the alignment motor (front) is driven for 3 sec
    E540
    0001
    The paper surface sensor remains unchanged 10 sec after the tray ascent/ descent motor is driven
    0002
    The tray upper sensor goes ON while the tray is moving up.
    0003
    The clock for the clock sensor is disrupted for 10 sec or more while the tray ascent/descent motor is driven
    E577
    0001
    The paddle does not leave home position when the paddle motor is driven for 2 sec or more
    0002
    The paddle does not return to home position when the paddle motor is driven for 2 sec or more
    0003
    The stack ascent/descent guide does not leave home position when the paddle motor is driven for 2 sec or more
    0004
    The stack ascent/descent guide does not return to home position when the paddle motor is driven for 2 sec or more
    E590
    0001
    The puncher does not return to home position when the puncher motor is driven for 250 msec
    0002
    The clock from the puncher motor clock sensor is disrupted for 60 msec or more when the puncher motor is driven
    E592
     
    In the course of sensor output automatic adjustment, the light-receiving voltage is 2.5 V or less even when the light-emitting voltage is set to 4.4 V. In the course of output automatic adjustment, the light-receiving voltage is 2.5 V or more even when the light-emitting voltage is set to 0 V. In the course of sensor output automatic adjustment, the light-emitting voltage is set to 4.4 V or more
    0001 to 0005
    Horizontal registration sensor
    0006
    Puncher waste full sensor
    E593
    0001
    The puncher not leave home position when the puncher shift motor is driven for 1 sec
    0002
    The puncher does not return to home position when the puncher shift motor is driven for 1 sec
    E5F1
    0001
    The folding roller does not leave home position when the stapler/folder motor is driven for 1.5 sec
    0002
    The folding roller does to return to home position when the stapler/folder motor is driven for 3.5 sec or more
    0003
    The clock is disrupted for 1 sec or more while the stapler/folder motor is driven
    Finisher-J1 Error Codes
    E500
    0000
    The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less
    E514
    0000
    At the start of the motor CW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON
    E530
    0000
    The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go ON. The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go OFF
    E531
    0000
    The stapling home position sensor (S16) does not go off 0.5 sec after the stapler motor is rotated CW. The stapling home position sensor (S16) dos not go ON with 0.5 sec after the stapler motor is rotated CW and, thereafter, the sensor does not go ON within 0.5 sec after the motor is rotated in reverse
    E537
    0000
    The aligning plate home position sensor (S6) does not go ON when the front alignment motor (M3) is driven for a specific number of rotations. The aligning plate home position sensor (S6) does not go OFF when the front alignment motor (M3) is driven for a specific number of rotations
    E577
    0000
    The return roller does not reach home position when the delivery motor (Ml) has been driven as much as will move it to the return roller home position sensor (S3)
    E580
    0000
    The delivery tray upper limit sensor (S13) goes ON while the delivery tray ascent/descent motor (M5) is in operation.
    The clock signal of the delivery tray ascent/descent motor clock sensor (S9) is not detected 15 times or more within 0.8 sec while the delivery tray ascent/ descent motor (M5) is in operation.
    The delivery tray paper height sensor (S10) does not go ON 4 sec after the delivery tray ascent/descent motor (M5) starts to move up.
    The delivery tray paper height sensor (S10) does not go OFF 4 sec after the delivery tray ascent/descent motor (M5) starts to move down
    E585
    0000
    At the start of the motor CCW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON
    Категория: Коды ошибок копировальных аппаратов,принтеров,МФУ | Добавил: avatar (07.10.2010)
    Просмотров: 3243 | Рейтинг: 0.0/0 |
    Форма входа

    Поиск

    Друзья сайта

    Статистика


    Copyright MyCorp © 2017